fbpx
search by application & industry

General Specifications – Group 22 Rotary Actuators

Download a PDF copy of the Group 22 General Specifications »

Output Torque and Timing

Model # Torque in lb-ft (N•m) Stroke Time (sec./100°)
configurable
Approximate Weight in lbs (kgs)*

22-309

3,000 (4,067)

30-300

515(234)

22-409

2,000 (2,712)

7.5-150

515(234)

22-409

2,500 (3,390)

10-200

512(234)

22-409

4,000 (5,423)

15-300

512(234)

22-809

8,000 (10,846)

15-300

1,100(567)

* Standard configuration weights shown, the actual weight may vary depending on the selected options.

Drive Current Rating in Amps (listed by operating voltage)**

Operating Voltage (Volts AC)
1- PHASE
3-PHASE
Model # 120 240 208 240 380 416 480 575
22-309
6.0
3.0
3.5
3.0
1.9
1.7
1.5
1.3
22-409

N/A

N/A
4.0
3.5
2.2
2.0
1.7
1.4
22-809
N/A
N/A
6.9
6.0
3.8
3.5
3.0
2.5

** Operating voltage tolerance is +10% to -15% and all drive models listed may be operated with a 60 Hz or 50 Hz frequency.

The gray shaded areas indicate the current rating for the standard operating voltage configuration. Non-standard operating voltages for model 22-309 and 22-409 are available with an optional transformer.

Additional Specifications

Operating Conditions –40° to 85° C. (–40° to 185° F.) 0 to 99% relative humidiy.
Demand Input Signal
Range
4–20 mA, 1–5 V dc
Minimum Step 0.1° typical
Linearity ±1% of span, max. independent error
Hysteresis 0.25% of span at any point
Demand Input Signal Characterization Linear: Drive output shaft moves
proportionally to the input signal.
Square: Drive output shaft moves
proportionally to the square of the input
signal.
Position Feedback Signal Demand input and position Feedback
signals are isolated from ground and the ac power line. Signal buffering provides 24 Vdc isolation between the Demand and Feedback signals.
Overtorque Protection If the output torque of the drive exceeds
115% of the drive rating, the motor will
shut off (feature can be enabled/disabled)
Action on Loss of Input Signal (Power On) Stays in place or runs to any preset
position (configurable)
Stall Protection If the motor tries to run in one direction for
more than 300 seconds (configurable from
30 to 300 seconds), the motor will shut off
Over-travel Protection Switches Two SPDT, one for CW and one for CCW
limit of output shaft travel. Standard switch
setting allows for 100° of travel.
Non-dedicated Switches (Field Adjustable) Two SPDT, rated for 1 A, 250 Vac
Handswitch Permits local electrical operation,
independent of demand input signal
Handwheel (and Handcrank on the model 22-809) Provides manual operation without
electrical power
Enclosure Precision-machined aluminum alloy
castings, painted with corrosion-resistant
polyurethane paint, provide a rugged,
dust-tight, weatherproof enclosure.
Mounting Orientation Upright, as depicted in outline dimension drawings
Customer Wiring Terminals accommodate up to 12 AWG (3.31 mm2)
Motor Does not coast or overshoot and will not overheat, even under continuous modulation
Gear Train High efficiency, precision-cut, heat-treated alloy steel and ductile iron spur gears enclosed in and permanently lubricated by a grease-filled housing are designed for long life and minimal wear.
Mechanical Stops Prevent over-travel during automatic ormanual operation
Standards*** cULus Listed. CE Compliant.

*** NOTE: May not be available with all options and models. For more information or to inquire about standards not specifically listed, please call
Beck at 215-968-4600.